Daily maintenance of CNC plasma pipe cutting machine
The diagonal cutting machine uses computer control, AC servo or step machine motor drive, the steel pipe end combination for automatic calculation and cut-off equipment.
With the intersection line cutting machine system program selection is convenient and fast, the display interface is intuitive and simplified, cutting accuracy and other advantages are widely used in all walks of life, the same do a good job of daily maintenance also allows you to use equipment safely and at ease during operation.
1. Maintenance of the cutting machine numerical control system
Strict compliance with operating procedures and routine maintenance systems; CNC equipment operators should strictly abide by operating procedures and daily maintenance system, the operator's technical business quality is the main factor affecting the frequency of failure. When the machine failure, operators should pay attention to retain the site, and to the maintenance personnel truthfully explain the situation before and after the failure, in order to facilitate analysis, diagnosis of the cause of the failure, timely elimination.
Prevents dust from entering the inside of the CNC device; In the processing workshop air will generally have oil mist, dust and even metal powder, once they fall on the cnc system circuit board or electronic devices, easy to cause the inter-component insulation resistance to decline, and even lead to components and circuit board damage. Some users in the summer in order to make the CNC system can overload long-term work, take to open the door of the CNC cabinet to dissipate heat, which is a very undesirable method, which will lead to the accelerated damage of the CNC system, should minimize the opening of CNC cabinet and strong electrical cabinet door.
Prevent the system from overheating; The individual cooling fans on the CNC cabinet should be checked for proper operation. Every six months or quarterly check the wind channel filter whether there is a blockage phenomenon, if the filter network dust accumulation too much, not clean up in a timely manner, will cause the temperature in the CNC cabinet is too high.
2. Maintenance of mechanical parts of the line cutting machine
Maintenance of the drivetrain; Regularly check the degree of lubrication of the drive shaft, replenish the amount of oil in a timely manner, clean the rails, screws, etc.;
Maintenance of the ball screw thread; Regularly check and adjust the axial clearance of the threaded thread of the screw to ensure the accuracy of the reverse drive and axial stiffness, regularly check whether the connection between the screw and the bed body is loose, the screw guard has damage to replace in time, to prevent dust or chips into, strictly abide by the operating procedures and daily maintenance system.
Maintenance of spare devices; When the spare device is not in use for a long time, it should be maintained regularly to prevent rust or device failure.
Air pressure system maintenance; Regular cleaning or replacement of the filter or filter of the air pressure system and water release to the air pressure system water filter.
Maintenance of machine accuracy; Regular machine level and mechanical accuracy checks and corrections are carried out. Generally to be carried out during the overhaul of the machine tool, such as the ball screw nut sub-pre-tightening adjustment reverse clearance.
Hubei Meisar CNC production of CNC plasma cutting machine equipment has been used in large-scale throughout the country. In Guiyang, Zunyi, Kunming, Yunnan Kunming, Dali, Qujing, Chengdu, Sichuan, Mianyang, Deyang, Panzhihua, Chongqing, Tianjin, Changshu, Taizhou, Jingjiang, Suzhou, Nanjing, Changzhou, Zhejiang Hangzhou, Shanghai, Shandong Jinan, Qingdao, Shaanxi Xi'an, Baoji, Gansu Lanzhou, Jilin Shenyang, Changchun, Harbin, Hainan Haikou Sanya, Inner Mongolia and other places, have the use of Mei Festival sub-ocean production of fully automatic CNC plasma cutting machine. Welcome to visit, visit, buy Messar plasma cutting machine. In addition to providing a new production of fully automatic CNC plasma cutting machine, but also for customers to transform the original CNC cutting equipment, including: replacement of CNC system, replacement torch, longer vertical guide, replacement operation software, precision adjustment, additional capacitance automatic height, arc pressure automatic height and other technical transformation!
Meisar CNC welcomes your call inquiry, contact phone number: +86 15171412223; We will be happy to answer for you!
